FlipMods https://flipmods.com/ Pinball Mods - Shooter rods & more! Mon, 24 Jun 2024 19:05:13 +0000 en-US hourly 1 https://wordpress.org/?v=6.9.4 219245622 Jersey Jack Soft Flipper Fix Kit Installation https://flipmods.com/sffk-installation/ Wed, 01 May 2024 01:30:17 +0000 https://flipmods.com/?p=2393 The post Jersey Jack Soft Flipper Fix Kit Installation appeared first on FlipMods.

]]>

Thanks for purchasing our FlipMods Jersey Jack Pinball Soft Flipper Fix Kit! We have put together this instructional video to help aid you in the install. If you have any questions, please contact us!

Installation Instructions

Still haven’t purchased a FlipMods JJP SFFK kit? You may do so below.

JJP Pinball Soft Flipper Fix Kit
JJP Pinball Soft Flipper Fix Kit
Jersey Jack Pinball Weak Flipper Fix
Jersey Jack Pinball Weak Flipper Fix
Jersey Jack Pinball Soft Flipper Fix Kit
JJP Weak Flipper Fix

JJP Soft Flipper Fix Kit (SFFK)

(3 customer reviews)

Price range: $60.00 through $120.00

Tired of the weak flippers in your Jersey Jack pinball machine? Introducing FlipMods JJP Soft Flipper Fix Kit! Installation service available!

 

JJP recently released an updated IO Driver board that has been used in recent games including Toy Story 4, The Godfather, and Elton John.  This board is almost identical to the existing board, with the exception of the capacitors (C701, and C702)  used for the 70V power section which is used for driving the high powered solenoids, as well as the flippers.

 

It is possible to retrofit existing older IO Driver boards with these new capacitors which provides the same benefit as the newly designed board, at a fraction of the cost. 

 

Due to the dimensional differences between the old and new capacitors, the new capacitors are too large to mount directly on the board.  A custom engineered standoff was designed to raise the new capacitor above the board.  Features of this standoff include:

 

  • The base matches the existing footprint of the older capacitor, ensuring that surrounding components on the board are not damaged, or obscured.
  • Provides an air gap between the surrounding bridge rectifiers and the capacitors.  This prevents the heat generated by the bridge rectifiers from conducting to the capacitors.
  • Provides accessibility to the surrounding fuses.
  • Polarity labeling (+ and -) to easily identify proper orientation while installing the assembly.
  • The top matches the diameter of the new capacitors to maximize surface area for maximum adhesion between the capacitor and the standoff.

 

Click the tabs below for additional information.

By using this modification, you acknowledge and agree that you are solely responsible for any consequences, including any damage or issues that may occur.

Clear
Categories: ,
Kit Details

Kit Details

This Kit contains everything needed to replace the 2 3300uF capacitors with larger 6800uF versions including

  • 2 Complete capacitor assemblies
    • Includes
      • High quality capacitors sourced from domestic suppliers.
      • Custom engineered stand offs to accommodate the larger capacitors.
      • 18 AWG solid Copper wire leads which are pre-soldered to the capacitors.
      • Bottom copper leads which can be directly soldered into the board.
      • Pre-installed adhesive between the capacitor and the standoff 
      • Adhesive backing to permanently mount the standoff to the board which reduces vibration forces on the capacitor.
  • 4 eyelets used for ensuring a good board connection for the new capacitors
    • The capacitors (original and new) contain snap leads which can easily damage the through hole plating if they are not removed / installed correctly.  If you are experienced at working with this type of capacitor, you may not need to install the eyelets.  
    • The positive side of the capacitors have traces that pass through the hole, so those holes are the ones most susceptible to damage.  The negative side does not use the through hole to connect the traces, but it is still recommended to install these eyelets for a more consistent install.
  • Alcohol swabs for preparing the top surface of the board to promote the best possible adhesion for the capacitor assembly
Installation Instructions

Installation Instructions

  1. Remove the existing capacitors at the top left of the board (C701, and C702)
    • The Hakko  solder remover is a good tool for this.
    • After removing the solder, gently straighten the leads, heat one lead, and gently push the capacitor while applying heat.  Repeat with the other lead, gently pushing the capacitor the other direction.  Repeat this rocking process to fully remove the capacitors.
  2. Solder the eyelets from the top of the board (if desired. See Kit Details tab above for more information about this).
  3. Apply Flux remover to the holes on the top of the board and then clean with the alcohol swab.
  4. Remove the adhesive cover on the  base of the capacitor assembly.
  5. Observe the proper orientation of the capacitor.  Use the polarity indicators on the capacitor and on the standoff to ensure proper orientation.  (Orientation should match the other 2 capacitors below C701, and C702
  6. Insert capacitors, and press down to ensure good adhesion between the board and the base of the standoff.
  7. Flip board over and solder the leads for both capacitors
  8. Trim leads 
  9. Apply Flux remover, and then clean using the second alcohol swab.
Installation Service

Installation Service

We are offering the kit + installation service for only $119.99 + return shipping to you, which you will pay for during checkout. After you purchase the kit and service, you will be contacted with further instructions on where to ship the board. Once we receive the board, we will immediately start working on it for minimal downtime. After we are done with the installation, we will send the board back and you will be all set!

 

Disclaimer: We cannot be responsible for any damage or issues that may occur as a result of this modification.

FAQ

FAQ

Click here to view our FAQ regarding our JJP Soft Flipper Kit Fix.

Reviews (3)

3 reviews for JJP Soft Flipper Fix Kit (SFFK)

    jmk.tgv
    January 1, 2026
    I'm thrilled with my two kits installed on my Hobbit and DialedIn pinball machines! The difference in responsiveness is striking. The gameplay is much more dynamic. Mike packed the equipment carefully, so it arrived in perfect condition at my home in Switzerland. I highly recommend them to all pinball enthusiasts!
    jmk.tgv
    January 1, 2026
    I'm thrilled with my two kits installed on my Hobbit and DialedIn pinball machines! The difference in responsiveness is striking. The gameplay is much more dynamic. Mike packed the equipment carefully, so it arrived in perfect condition at my home in Switzerland. I highly recommend them to all pinball enthusiasts!
    Chris Wolf
    February 13, 2024
    This kit was straight forward and was easy to install. My JJP GNR has full flipper strength! Would highly recommend!
Add a review

Related products

The post Jersey Jack Soft Flipper Fix Kit Installation appeared first on FlipMods.

]]> 2393 Spike 2 Click Fix Installation https://flipmods.com/click-fix-install/ Fri, 26 Apr 2024 18:23:35 +0000 https://flipmods.com/?p=2353 The post Spike 2 Click Fix Installation appeared first on FlipMods.

]]>

Thanks for purchasing our FlipMods Spike 2 Click Fix Board! We have put together this instructional video to help aid you in the install. Total installation time is about 30 seconds and requires no tools! If you have any questions, please contact me!

Installation Instructions

Still haven’t purchased a FlipMods Spike 2 Click Fix Board? You may do so below.

Stern Spike 2 Click Fix Board
Stern Pinball Spike2 Click Fix Mod
Stern Pinball Spike 2 Click Fix Mod
Stern Spike 2 Click Fix Board
Stern Pinball Spike 2 Click Fix Mod

Spike 2 Click Fix Board

(1 customer review)

$60.00

It’s been well documented here on Pinside that many new Stern Spike 2 games (2021+) are excessively clicking on boot, coming from the power supply (PDB). We have developed a safe, plug-and-play solution that installs within seconds!

Before & after video:

Categories: , , , , , , , , ,
Installation Instructions

Installation Instructions

Reviews (1)

1 review for Spike 2 Click Fix Board

    Shawn Knapp
    May 6, 2024
    Went from 1000 clicks to zero! Thanks!
Add a review

Related products

The post Spike 2 Click Fix Installation appeared first on FlipMods.

]]> 2353 Jaws RGB Ramp + Shark Cage Illumination Kit Instructions https://flipmods.com/jaws-rgb-ramp-shark-cage-illumination-kit-instructions/ Sun, 14 Apr 2024 17:11:23 +0000 https://flipmods.com/?page_id=2309 The post Jaws RGB Ramp + Shark Cage Illumination Kit Instructions appeared first on FlipMods.

]]>

Thanks for purchasing our FlipMods Jaws RGB Ramp & Shark Cage Illumination Kit! We have put together these instructions to help aid you in the install. Total installation time is about 1 hour and only requires a Phillips head screwdriver. If you have any questions, please contact me!

Installation Instructions

  1. Power down your pinball machine and unplug it to be safe.
  2. Remove the glass and all pinballs. Premium / LE models can skip to step 4.
  3. If your game is a Pro model, locate the shark tank on the playfield and remove the screws notated in the picture below. Then, remove the top and right side plastic.
Jaws Shark Cage Illumination
  1. Lift up the playfield and locate the plug indicated in the picture below.
  1. Disconnect the plug and install our harness inline. Premium / LE models can skip to step 8.
  1. Route the single rectangle RGB holder at 1 end of the RGB harness up through the rectangular cutout up into the shark tank. The 2nd picture indicates how you will install the black RGB housing under the metal bracket that the top shark cage plastic was attached to.
  1. Lower the playfield and place the stock top shark tank plastic where you removed it from and while holding the black rectangular RGB board holder in place under the stock metal bracket (with the LED diode facing down), install the included long screw where the red arrow is, through the stock plastic (making sure the holes line up), into the bottom hole of the RGB housing. *Note* The screws will be tight, this is by design. Use 1 of the stock screws you removed where the green arrow is. Reinstall the stock side plastic of the shark tank with the stock screws.
  1. It’s time to install the ramp lights now. Let’s raise the playfield again and route the end of the wire harness that has 2 RGB boards attached to back of the backboard. Remove the stock screw as indicated by the arrow below, install the RGB bracket with the stock screw. You’re all done!! Enjoy!

Haven’t purchased your Jaws RGB Ramp & Shark Cage Illumination Kit yet? You can below!

Jaws Pinball Shark Cage Light Mod
Jaws Pinball Shark Cage Illumination Mod
Jaws Pinball Shark Cage Light Mod
Jaws Pinball Shark Cage Light
Stern Jaws Pinball Ramp Illumination Mod
Stern Jaws Pinball Ramp Illumination Mod
Jaws Pinball Ramp Lights
Jaws Pinball RGB Light Mods
Stern Jaws Pinball Mods
Jaws Pinball Shark Cage Mod
Stern Jaws Pinball Shark Mod
Jaws Pinball Mods
Jaws Pinball Shark Cage & Ramp Illumination Kit

Jaws RGB Ramp + Shark Cage Illumination Kit

Price range: $55.00 through $95.00

Add some light to the ramps on your Jaws Premium / LE pinball machine, as well as ramps + shark cage on your Jaws Pro! This kit installs inline with your RGB illumination and provides RGB illumination in sync with the GI lights in the game in the dark ramps & shark cage. Our custom built wire harness and mounts are easily installed and are completely interactive. No permanent game modifications are required.

We are producing these kits now, so please allow a few weeks for production.

Clear
Categories: ,
Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Jaws RGB Ramp + Shark Cage Illumination Kit”

Related products

The post Jaws RGB Ramp + Shark Cage Illumination Kit Instructions appeared first on FlipMods.

]]> 2309 Venom Ravencroft Installation Instructions https://flipmods.com/venom-ravencroft-installation-instructions/ Fri, 12 Jan 2024 15:30:27 +0000 https://flipmods.com/?page_id=1698 The post Venom Ravencroft Installation Instructions appeared first on FlipMods.

]]>

Thank you for purchasing FlipMods’ Venom Pinball Ravencroft mod! Installation should take between 1-3 hours and requires a medium & small Phillips head screwdriver and your pinball nut driver set. Long screwdrivers and playfield jacks (or a way to prop up the back of the playfield) help a lot.

A HUGE thanks to Andy from Rocket City Pinball for putting together this amazing installation video.

The following writeup is how I have been installing this mod throughout the duration of designing and building it. You may find a different way is better for you which is fine, there’s usually more than one way to do something in pinball!

First things first, as always shut off your game, remove the glass and all balls.

  1.  Now, let’s remove the Carnage ramp. Lift the playfield and locate this nut directly below Carnage and unscrew it. Also unplug the marked harness.
  1. Lower the playfield so we can work on the top for a bit. Remove this screw behind the stock Ravencroft house plastic. A magnetic screwdriver is helpful. We will reuse this screw later so hang onto it.
  1. Unscrew the 2 small Phillips head screws holding the Ravencroft arch plastic. Put these screws aside, they will be used again. If you purchased only the arch, continue to step 14.
  1. Disconnect the 3 wire harnesses behind the playfield that connect the Carnage bash toy ramp.
  1. Be mindful of the spring below the playfield that controls the carnage ramp movement. It may be helpful to tape it to the coil mount or coil to help keep it in place. Not necessary, but may help.
  1. You’re ready to remove the carnage ramp. It pulls up off of the playfield. It will take a little elbow grease, but it will pull up and off. I have been pulling up from the rear of the ramp as well as near the captive wall as see in the picture below.

Be mindful of the wire harness that you disconnected below the playfield that will pull up through the playfield, as well as the harnesses in the back and the linkage on the bottom of the carnage ramp.

  1. Once the carnage ramp is off, put it down somewhere so we can remove a few nuts from it. Starting on the left side (pic 1), remove the 2 nuts then remove the bracket holding the original left gate. This bracket and gate is staying off, you can put it away. I put the nuts back on the side of the ramp even though they don’t do anything anymore. On the right side, remove the 3 marked nuts and marked spacers (pics 2) so that we can remove the right side bracket and gate. We will be replacing the large and small white spacers from the middle screw marked in the 4th picture below with the included spacer in the Ravencroft mod kit (3rd picture below). We won’t be using the 2 stock spacers anymore, so you can put them away as well. You do need to reinstall the stock spacer on the right screw (4th pic, yellow arrow). Reinstall the nuts on this side.
  1. It’s time to remove the main Ravencroft house now. You only need to remove the marked screws below to remove the plastic from the playfield. *NOTE* There are plastic spacers behind the Ravencroft house plastic. It’s okay if they drop onto the playfield while unscrewing. We will not be reusing these spacers but we will be reusing these long black screws.
  1. Now that the Ravencroft house is removed, let’s remove the LED boards and attach them to the new Ravencroft mod. We will not be removing the metal brackets behind the house since the mod has them built in. Loosen the nuts marked below. You will need to hold the screw on the front in place with a Phillips head screwdriver. We will not be reusing these nuts and screws.
  1. Next, attach the LED boards to the back of the new Ravencroft house using the supplied screws and nuts, not the stock ones. You will notice a “2R” and “1R” marking on the back of the house, this indicates which board to install. The “2R” indicates 2 red wires on the board while the “1R” indicates 1 red wire on the board, as seen below.
  1. It’s now time to attach the new Ravencroft house to the playfield using the long screws from step 8. As mentioned, instead of reusing the spacers from step 8, the back of the house has them built in. Insert the long screws into the holes that have the long spacers around them before you put the new house in place, especially the screw behind the front gate (as shown in the picture below). This will make it easier to install the new house.
  1. Let’s install the new house to the backboard, but first we need to route the wires through. The smaller fence of the Ravencroft (on the left side) wiring should be routed through the large opening, near the post holding the screw that you unscrewed in step 2. The larger fence of the Ravencroft house (on the right side) should be routed as seen in the 2nd picture below. There is a small opening in the metal plate in the backboard that you can run the wire through, but make sure it stays above the opto. Once the wires are safely through, you may screw the new Ravencroft house into the backbox.
  1. It’s time to install the carnage ramp we removed back in step 6. Make sure to route the wire harness in the front of the ramp under the playfield before securing the ramp in place. Also, remember when I said to be mindful of the spring back in step 5? Now is when we need to install the spring properly over the plunger, under the playfield.

 

Once you know the plunger and spring are secure and the plunger is inside the coil, you can reinstall the nut under the playfield that you removed in step 1 and the screw in step 2.

  1. Install the new archway where we removed the stock one, using the 2 small stock black screws, then run the wire next to the Carnage ramp opto wiring, as seen in the 2nd picture below. When installing the archway, try to push it toward the middle of the playfield as much as possible, then tighten the screws. This way everything has clearance and rests where it should.

 

Those sweet Symbiote flasher covers you see are made by Rocket City Pinball and can be purchased here.

  1. Now that all the wiring is routed, let’s get it all connected. First, let’s use the 2nd red light in the backboard (3rd light total) to power everything by connecting the included alligator clips to it as shown in the pictures below. *NOTE* This bulb is not a regular GI bulb. After that, connect all the lighting to the 3-way splitter and connect the 3-way splitter to the end of the alligator clips you just installed.

That’s it! You successfully installed your Venom pinball Ravencroft mod by FlipMods! Test everything out and make sure it’s all working and as always, go get a high score!

Still don’t have your Venom Ravencroft mod? Purchase below!

Venom Pinball Ravencroft Mod
Venom Pinball Ravencroft Mod
Venom Ravencroft Mod - Image 3
Venom Ravencroft Mod - Image 4
Venom Ravencroft Mod - Image 5
Venom Pinball Ravencroft Mod
Venom Pinball Ravencroft House Mod
Venom Pinball Carnage Arch Mod

Venom Ravencroft Mod

$150.00

Unleash the symbiote within! Replace the lifeless Ravencroft plastics with this interactive illuminated, 3D Ravencroft mod! This multi-part mod features 16 LED’s shining through translucent red windows on the house, gate and lantern for maximum gameplay effects. Transform the iconic Ravencroft Institute into a dynamic, light-infused centerpiece for your Venom pinball machine. Aside from looking great, this mod adds another dimension of fun to bashing that carnage captive ball! Includes house, arch + everything needed to install and illuminate.

Categories: , Tags: ,
Description

We are currently out of stock but plan on making more and will make more once you order. Please allow a few weeks!

Installation Instructions

Installation Instructions

Click here for installation instructions for the Ravencroft mod.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Venom Ravencroft Mod”

Related products

The post Venom Ravencroft Installation Instructions appeared first on FlipMods.

]]> 1698 Venom Scoop Illumination Kit Installation Instructions https://flipmods.com/venom-scoop-illumination-instructions/ Fri, 20 Oct 2023 00:47:17 +0000 https://flipmods.com/?page_id=1417 Instructions on how to install your FlipMods Venom scoop illumination kit in your pinball machine.

The post Venom Scoop Illumination Kit Installation Instructions appeared first on FlipMods.

]]>

Thanks for purchasing our FlipMods Venom Scoop Illumination Kit! We have put together these instructions to help aid you in the install. Total installation time is 5 minutes or less and only requires a Phillips head screwdriver. If you have any questions, please contact me!

Installation Instructions

  1. Power down your pinball machine and unplug it to be safe.
  2. Remove the glass and all pinballs.
  3. Lift the playfield in the upright position.
  4. Locate the scoop toward the back of the playfield, as seen in the picture below.
  • playfield-location
  1. Unscrew the 2 screws that the arrows are pointing to in the below picture, directly next to the “NO NUTS ON STUDS” (LOL) sticker.
  • scoop-illumination-installation
  1. Using the 2 screws that you just removed, install the bracket (with bulb installed in the bulb holder), with the LED light pointing toward the scoop. You can move the bulb holder up and down to adjust the angle.
  2. Locate a GI bulb that you would like to tap off of, there is one to the left of where you just installed the bracket. Peel back (or cut carefully with a razor blade) the heat shrink indicated in the picture below to expose the factory solder. Hook the red alligator clip to the wire that the red arrow is pointing to and the black to the wire the black arrow is pointing to. Install the extension from the end of the alligator clip to the end of the bulb socket.
  • GI-bulb

You’re all done!

Haven’t purchased your FlipMods Venom Scoop Illumination Kit yet? You can below!

Venom Scoop Illumination Kit
Venom Scoop Illumination Kit Blue

Venom Scoop Illumination Kit

(2 customer reviews)

$15.00

Easily light up the scoop on your Venom pinball machine with our scoop illumination kit. Available for Venom Pro, Premium & LE models, this kit includes our custom designed mount, alligator clips, 12″ matrix extension cable, a 4SMD LED bulb and wedge socket.

Clear
Categories: , Tags: ,
Creative Commons

Creative Commons

The Insider Connected coin door covers were created by MisterBlik and are available on Thingiverse – https://www.thingiverse.com/thing:5232305

If you are MisterBlik, please contact me! I have tried to reach you on multiple platforms without success.

The apron covers were created by me 🙂

Reviews (2)

2 reviews for Venom Scoop Illumination Kit

    D
    February 23, 2025
    Looks really good under the Daily Bugle mod. Red was a good choice in my opinion. Simple install, too.
    Christopher Hills
    December 11, 2023
    Super easy mod to add Daily Bugle illumination light. Loots great. I went read, if I had to do again, I would do it blue!!
Add a review

Related products

The post Venom Scoop Illumination Kit Installation Instructions appeared first on FlipMods.

]]> 1417 Venom Bell Tower Mod Installation Instructions https://flipmods.com/bell-tower-install/ Thu, 28 Sep 2023 17:46:59 +0000 https://flipmods.com/?page_id=1262 The post Venom Bell Tower Mod Installation Instructions appeared first on FlipMods.

]]>

Thanks for purchasing our FlipMods Venom Pinball Bell Tower Mod! We have put together a video and these instructions to help aid you in the install. Total installation time is 30 minutes or less on the pro version (longer on Premium / LE) and only requires a Phillips head screwdriver. If you have any questions, please contact me!

Installation Instructions

*NOTE* These instructions are based off installation on a Pro model, however, Premium & LE are very similar and covered below. Also, it is easier on the Pro to remove the bell tower than it is on Premium & LE, so if you don’t want to remove the building, you don’t have to. The Premium / LE install requires a little more work than the pro version.

  1. Power down your pinball machine and unplug it to be safe.
  2. Remove the glass and all pinballs.
  3. Lift the playfield in the upright position.
  4. Locate the wire harness that is attached to the bell tower and disconnect it.
  • step3
  • step3a
  1. This step is not necessary, but it certainly helps. It will be easier if you tape an extra wire to the wire harness so when you are ready to pull the wire harness back under the playfield, you can use the wire to assist.
  • step4
  1. Lower the playfield and locate the bell tower. Remove the 2 screws in the front on the bottom. This is what holds the bell tower in place. *NOTE* I recommend putting a clean rag on the playfield, this way you protect the playfield and parts.
  • step5
  1. a) Lift the bell tower up and over the bracket which holds it in place, and place it down on the rag on the playfield. If you taped a wire to the harness on the bottom of the playfield, be sure not to pull it all the way through.
  • step6a
  1. b) Remove the tape from the wire and wire harness
  2. Once the bell tower is removed from the playfield, bring it over to your work bench or a flat surface to work on. Then, locate the 2 screws on the roof, the 1 screw on the bottom of the right side, and the 1 screw on the bottom of the left side, and remove them. It’s easier to remove the roof first. This will disassemble the bell tower completely. *NOTE* Keep all these screws as we are reusing them.
  • step7 (1)
  • step7b
  1. Now that the bell tower is apart, it’s time to install the panels. Starting with the left side, remove the backing of the double sided tape on the Venom Bell Tower Mod’s left side panel. Next align the bottom screw hole on the Bell Tower Mod with the bottom screw holes on the stock bell tower, and the window on the mod with the window on the stock bell tower. *NOTE* If the flasher boards get in the way, you can carefully bend the bracket back a little bit or use the 2 included black spacers instead of the stock white spacers to move the flasher boards back a bit.
  • step8
  • step8leftpanel
  • step8spacer
  1. a) Once the left side is installed, it’s time to install the right side next. The order of the installation of panels matters, front should be last.
  • step8a

Illumination Kit Step

  1. b) If you purchased the illumination kit for your Pro model, we need to mount the bulb on the interior of the bell tower, on the left hand side, using the stock screw hole and screw. Don’t tighten it all the way yet.
  • step8b
  • step8c
  • step8d
  • step8e
  1. b) If you purchased the illumination kit for your Premium or LE model, we need to mount the 2 LED strips on the interior of the bell tower, on the left and right hand side of the mount, using the double sided tape on the strips. Install the splitter above the playfield and later on pull thru same hole as stand-up target directly in front of bell tower.
  • 393907946_1359471141367315_7457051163613656278_n (1)
  • 394389096_888712982609671_8900208025298743771_n (1)
  1. c) Now let’s go back to the right side, remove the double sided tape backing on the Bell Tower Mod right side panel, line up the screw hole and window and screw the right side in with the stock screw. Don’t tighten all the way yet. 
  • step8f
  1. d) Time to install the front panel. The reason why we install the front last is because the sides of the front panel overlap the left and right side panels to give the building a clean, uniform look. The brick pattern continues around the sides, making it look as real as possible. Remove the double sided tape backing on the Venom Bell Tower Mod front panel, then align the 2 holes on the bottom and the window with the front of the stock bell tower, and affix the front panel.
  • step8g
  1. e) Now that the front panel is installed, you can loosen the left and right sides a bit and push those panels toward the front to align them even more. *NOTE* The roof will be installed once in the machine.
    f) Go back to the pinball machine and prepare to reinstall the Venom Bell Tower Mod. If you pulled a wire in step 5, tape the bell tower harness to that wire.
  • step9
  1. Place the bell tower somewhere safe (propping it on the bell tower mount works, but be careful) and lift the playfield in the upright position again.
  2. If you purchased an illumination kit, let’s connect it to the closest GI bulb. I included a red and white LED bulb with the kit, so depending on which color you choose will dictate which bulb you connect to.
  • step10

*NOTE* I am using the red GI bulb because I used a red bulb in the bell tower. Pull back the wire shrink on the wires of the GI bulb that you choose to expose the terminals. Attach the alligator clips to the terminals with the red clip being on the red wires and the black clip being on the yellow wires.

  • step10a
  1. a) Feed the illumination kit wiring through the hole underneath the target in front of the bell tower while grabbing it above the playfield. Slowly pull a little bit above the playfield, being careful not to pull too much.
  • step10b
  1. Next, carefully pull the wire that you taped to the wire harness through the playfield to pull the stock harness through. *NOTE* You may have to use tweezers or something to get the Molex connection through the playfield.

Connect the stock harness back and remove the wire that you used to feed the wire harness through the playfield.

  • step11
  1. Lower the playfield to start mounting the bell tower back in place. First, connect the illumination kit wiring to the bulb wiring. Then, carefully slide the bell tower over the mounting bracket being careful of the wiring. You may have to push some of the illumination kit’s wiring back below the playfield. *NOTE* Make sure the wiring is behind the target and not in front of the opto in the Life Foundation loop.

Screw the bell tower back onto the bracket using the stock screws and the 2 holes on the front of the tower.

  • step12
  • step12a
  • step12b
  1. Finally, let’s install the roof! Line up the 2 holes on the sides and install 1 of the stock screws loosely. Next, install the other stock screw on the other side and tighten both screws.
  • step13

You’re all done! The next step is to go get a new Grand Champion score!

Haven’t purchased your FlipMods Venom Bell Tower Mod yet? You can below!

Venom Bell Tower Mod
Venom Pinball Belltower Mod
Stern Venom Pinball Bell Tower Mod
Venom Pinball Bell Tower Mod by FlipMods
Venom Pinball Bell Tower Mod by FlipMods
Venom Pinball Bell Tower Mod by FlipMods
Venom Pinball Mods
Venom Bell Tower Mod illumination kit
Venom Pinball Belltower Illumination Kit
Venom Pinball Bell Tower Modification

Venom Bell Tower Mod

(1 customer review)

$70.00

Introducing FlipMods’ Venom bell tower mod! Replace that boring, 1-dimensional bell tower with this custom 3-Dimensional bell tower kit. Includes 4 panels (front, left, right & roof) for the Pro, Premium & LE models. Installation is simple and not permanent, it can be easily removed any time. We also offer an illumination kit which includes all hardware necessary to light up the interior of the belltower red.

Clear
Categories: , Tags: ,
Installation Instructions

Installation Instructions

For written instructions, click here.

Reviews (1)

1 review for Venom Bell Tower Mod

    Terry Candlish
    February 20, 2024
    Looks great1 Much better than the stock tower!
Add a review

Related products

The post Venom Bell Tower Mod Installation Instructions appeared first on FlipMods.

]]> 1262